Croker Oars
  • HOME

  • SCULLING

  • ROWING

  • SURF & OCEAN

  • OCEAN ROWING

  • SALE ENQUIRY

  • CONTACT US

  • INTERNATIONAL

  • More

    Replacing sleeves

     

    Replacing MK3 Asymmetrical Sleeve

     

    The following information is to help you replace your sleeves. It is viable for all sculling and rowing.

     

    1. Remove old sleeve and clean excess glue from shaft.

    2. Place oar on pitching bench (as per attached video).

    3. Read the engraving S or B on the inside of the sleeve to make sure they are pointing in the right direction - see below. 

    4. Fill the grooves inside with glue mixture. (Epoxy resin available from BCF and view a detailed video on website to mix glue.) We use a 2 pack epoxy resin combined with a lightweight filler such as micro balloons, Q Cell or similar.

    5. Clip sleeve body around shaft at desired position.

    6. Rotate sleeve back & forth a few times to ensure good coverage of glue on shaft. Wipe away any excess glue.

    7. Using a spirit level across the back of the sleeve, set the desired pitch. All new Croker Oars are set at 0°.

    8. Leave oar in a dry position to allow glue to set, trying not to bump the sleeve.

    9. Small alterations (<0.5°) may be made to dry sleeves by scraping one edge of the back. 

     

    Bow side sleeve

    BOW SIDE - face sleeve letter (B) towards blade

    Stroke side sleeve

    STROKE SIDE - face sleeve letter (S) towards blade

    Replace MK1 Symmetrical Sleeve
     

    1. Remove yellow button with a screw driver.

    2. Remove old sleeve with chisel and draw knife.

    3. Place oar on pitching bench (as per video).

    4. Read the engraving inside the sleeve to make sure you have the right sleeve (not applicable to surf oars).

    5. Heat the sleeve with warm air for a few minutes before fitting.

    6. Use a piece of timber to hold the sleeve body open and fill the ridges inside with glue and filler mixture. We use a 2 pack epoxy resin combined with a lightweight filler such as micro balloons, Q Cell or similar. (Epoxy resin available from BCF and view a detailed video on website to mix glue.)

    7. Clip sleeve body around shaft at desired position

    8. Try to get the body even and level before pushing the back on. Less correction will be needed (no twist).

    9. Click the back on to the end of the sleeve and push firmly forward using a small block of wood, which has a concave shape to fit over the oar shaft.

    10. Rotate sleeve back and forth a few times to ensure good coverage of glue on shaft.

    11. Wipe away any excess glue.

    12. Using a spirit level across the back of the sleeve, set the desired pitch. All new Croker Oars are set at 0°.

    13. Leave oar in a dry position to allow glue to set, trying not to bump the sleeve.

    14. Small alterations (<1°) may be made to dry sleeves by scraping or planing one edge of the back. (See directions Set Pitch on Sleeve to 0°.)

     

    Please contact us if you have
    any questions

    Phone 0748 725 6783

     

    0748 725 6783

    SEAT TOPS
    EVENTS
    SUPPORT
    GALLERY
    CROKER OARS
    VIDEOS
    • Facebook - White Circle
    • Instagram - White Circle
    • Twitter - White Circle
    • YouTube - White Circle
    FOOT STRETCHER
    SHOP
    0

    © 2019 Croker Oars. All Rights Reserved

    Croker Oars UK

    ph. 0748 725 6783

    Contact Us

    Join Our E-Newsletter
    • Facebook - White Circle
    • Instagram - White Circle
    • Twitter - White Circle
    • YouTube - White Circle
    Visit our Privacy Policy